NEWS
Views: 0 Author: Site Editor Publish Time: 2026-11-16 Origin: Site
A double seal runs on a small volume of liquid held between two sets of faces, well away from the process stream. Both ends read that liquid. A spec that names one compatibility and stops has left half the job undone.
Two face pairs sit back to back, and barrier fluid fills the space between them. Process touches the inner pair on one face, barrier on the other. Out past the outer pair the same barrier meets plant air. Whatever goes in that space has the process and the plant reading over its shoulder. Choose it for one side and the other side still has to live with the result.
First comes the process. Barrier that leaks inward ends up in the product, which is why mineral oil in a caustic line writes a contamination report and glycol in a hydrocarbon stream turns up in the drum. A batch that cannot carry trace oil sets the search in motion from that side. The compatibility chart gets the job moving. It never finishes it.
Outward leakage reaches the gland and whatever sits around it. Fluids that rest quiet in the bottle can turn sour once air gets at them. Volatile ones evaporate and leave the reservoir low, and a fluid that barely touches the process can still make a mess on a warm pump. One bottle has to serve the whole gap.
Leak direction is a pressure question. Keep barrier above the process and leakage bleeds into the product while the pot stays clean. Drop below that line and process fluid walks in, turning the vessel into a second process loop full of chemistry nobody rated it for. That margin has to hold through startup, run speed, and the coast down. Chemistry alone never saved a seal running the wrong pressure.
Heat has to go somewhere. A small pot with a cooler keeps up on a modest duty; a bigger one wants an external loop dragging heat off the faces. A liquid that clears every compatibility check still cooks when the loop cannot pull the heat away. Fluid and circuit belong in the same decision, before the unit goes out.
A barrier picked off the process side alone gets half the job done. Both sides of the gap have to clear the same liquid, pressure has to sit above the process, and the loop has to carry heat off the faces. With those settled the seal keeps turning. FBU builds double cartridge seals across the API 682 arrangements for pump programs. Final compatibility, pressure, and thermal limits live on the data sheet for the exact model.
Where it sitsBetween two face pairs. Process touches one side of the inner pair, plant air the other side of the outer. Both ends read the barrier.
Process sideInward leakage enters the product. Mineral oil in caustic, glycol in hydrocarbon. Start from the compatibility chart.
Outside sideOutward leakage reaches the gland. Volatile fluids drop the reservoir level. Exposure can turn a fluid sour.
PressureKeep the barrier above process pressure. Seepage then bleeds into the product and the pot stays clean. Below that line the process walks in.
CirculationA small pot with a cooler handles modest duty. Bigger load needs an external loop. An otherwise good fluid still cooks without heat removal.
Which fluid should a double seal barrier be compatible with?
Both sides. Inner faces see process and outer faces see plant atmosphere. Barrier that leaks inward enters the product, and barrier that leaks outward reaches the gland. One liquid has to clear both environments.
Why must barrier pressure stay above process pressure?
A pressure difference sets the direction. Barrier held above the process leaks inward into the product and the reservoir stays clean. Below process pressure the flow reverses and the vessel fills with process fluid. That margin has to survive startup, full speed, and the coast down.
Can a volatile barrier fluid cause problems?
Volatile fluid evaporates and drops the reservoir level. A low level erodes the pressure margin the seal depends on. Exposure to air can also turn a fluid sour that sat quiet in the bottle.
Does the outside environment matter for barrier selection?
It does. Leakage past the outer faces reaches the gland and the air around it. A fluid harmless to the process can still make a mess on a warm pump. One fill has to work at the inner and outer ends.
When is an external circulation loop needed?
When the duty outgrows a small cooled reservoir. Bigger heat loads at the faces need an external loop to pull heat away. Fluid that looks right in the bottle still cooks when the loop cannot shed the load.
QUICK LINKS
Seal Water Flow Meters
CONTACT US
+86-512-57011188
No.183 , Yinhe Road, High Tech Industrial Development Zone Changshu Suzhou, Jiangsu, China Postal Code: 215533
Copyright © 2026 FBU Sealing Technology (Suzhou) CO.Ltd. All Rights Reserved.
Copyright © 2026 FBU Sealing Technology (Suzhou) CO.Ltd. All Rights Reserved.